This is a WIFI 2.4G 4dbi PCB Board Antenna.
Features:
Frequency 2400 ~ 2500 MHz
S.W.R. = 1.0 Kg
Environmental:
Operation Temperature - 40 °C ~ + 65 °C
Storage Temperature - 40 °C ~ + 80 °C
Application:
IEEE 802.11 b/g/n WLAN System
Wireless Communication System
Wi-Fi ..
Wireless 433MHz Garage Door Remote Control 4 buttons for 4 different garage doors, electronic rolling doors, or RF 433MHz retractable doors.
It is widely used in remote control switches, receiving modules, motorcycles, automobile anti-theft products, family anti-theft products, electric doors, ro..
This is WS2812 RGB LED Controller Adapter Module for ESP8266 ESP-01. You can make a colorful display project for Arduino IDE.
Features:
Interface: 3Pin connector.
Support 3.7V lithium battery.
It is based on ESP-01/ ESP-01S.
It supports Arduino IDE programming.
Package includes:
..
This is WXD3-13-2W 10K ohm Precision Potentiometer, widely used to adjust the timer, speed, and temperature.
Features:
Model: WXD3-13-2W
Small size, easy to carry
Provide full protection from dust, shock, scratches and bumps, and other daily damage.
Package Includes:
1 x WXD3-13..
This is WXD3-13-2W 4.7K ohm Precision Potentiometer, widely used to adjust the timer, speed, and temperature.
Features:
Model: WXD3-13-2W
Small size, easy to carry
Provide full protection from dust, shock, scratches and bumps, and other daily damage.
Package Includes:
1 x WXD3-1..
WZ3605E 80W 5A Adjustable Buck Boost Power Supply Module is a high-definition color screen display that is clear and intuitive, using a 1.44-inch high-definition color screen LCD display, and the content is displayed on multiple screens. The output voltage is adjustable from 0.6-36.00V, and the outp..
X9C103S DC 3-5V Digital Potentiometer Board Module for Arduino consists of a resistor array, wiper switches, a control section, and non-volatile memory. The wiper position is controlled by a three-wire interface. These are digitally controlled (XDCP) potentiometers.
The potentiometer is implemen..
The X9C104 digital potentiometer module helps you simulate the mechanical control of a potentiometer. The integrated circuit contains 99 series-related resistors. With a microcontroller, you can control the module and select the place where the center pin of the "potentiometer" is connected, anywher..
The XBee Shield V03 Module allows wireless communication between Arduino over a modified ZigBee protocol using Xbee Module. The shield is ready to use, plug n play, without the Xbee Module. The shield can be directly put on top of Arduino Uno. It works with all Xbee Module i.e. Series 1 and Series 2..
This is a simple to use, RS232 to the serial base unit for the XBee line of products. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach an RS232 cable, attach a USB cable to power the board and you will..
XBee Sensor Expansion Shield V5 with RS485 and BLUEBEE Bluetooth Interface for Arduino provides a number of interfaces that are commonly used, it includes Bluetooth, SD cards, APC communication, and RS485. Also, standard UART and 12C are also made easy to access. It is designed for easy connecting o..
This is the XBee Pro S2B module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication betwee..