This is a torque RF 370 DC Motor, when the power supply is 6V, it is about 10000 revolutions per minute. The no-load current is 0.06A and the locked rotor current is 0.91A.
Features:
Motor Diameter: 24mm
Motor Length: 31mm (excluding shaft)
Motor Shaft Diameter: 2mm
Shaft Length: 4mm
..
Description:
L293D Motor Driver Module is a medium power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L293 motor driver IC. It can drive 4 DC motors on and off, or drive 2 DC motors with directional and speed control.
The driver greatly simplifies and in..
L293D Motor Driver module is compatible with ESP12E Dev Kit and NodeMCU. This shield board is driven by the power full-bridge chip L293D which can directly drive 2-channels DC motors or one-channel stepper motor.
In this motor shield board, the IO port of ESP-12E Dev Kit is used as the control po..
L298N 2-way Dual H-Bridge DC Driver Module can drive two DC motors or 4-wire 2-phase stepper motors and achieve forward rotation or reverse rotation. It is possible to adjust the rotation speed. Each can provide a continuous current of 1.5A, peak current can be up to 2.5A, has thermal protection, an..
L298N based Motor Driver is a high-power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L298N Dual H-Bridge Motor Driver chip and is powerful enough to drive motors from 5-35 Volts at up to 2 Amps per channel. This motor driver is perfect for robotics and mechatr..
L298P 2A Dual Channel DC Motor Driver Shield Module is based on the L298, which is a full deck driver designed to drive inductive loads such as relays, solenoids, DC motors, and stepper motors. It allows you to drive two DC motors with your board, controlling the speed and direction of each one inde..
Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A. Use eight high-speed Schottky diodes at the motor output as protection. Stack design can be directly plugged into the Arduino, easier to use.
The L298P shield DC motor driver has..
L6470 Stepper Motor Driver Board is based on the STMicro L6470 dSPIN stepper motor driver. It allows you to control a stepper motor with a voltage from 8 to 45V at 3Arms over an SPI connection. It has built-in overcurrent detection, Undervoltage detection, overtemperature detection, stall detection,..
This Module is based on the L9110 Motor Driver IC. It can drive 4 DC or can drive two 4-wire 2-phase stepping motors.
Features:
Module supply voltage: 2.5-12V
It can drive 4 DC motors
Application: DIY smart car robot motor
Package Includes:
1 x L9110S 4-Channel DC Motor Driver B..
Makerbase MKS TMC2160-OC Stepper Motor Driver has two working modes, SpreadCycle(without mute function) and StealthCHop(with mute function) mode. It can be switched via DIP Switch.
Features:
Model : MKS TMC2160-OC
Capable of driving up to 4.33A of current.
Easy to operate, Max supports..
Aluminum Servo Horn Rocker Arm 25T For MG995 MG946R MG996R MG945 S3003 RC Model Motor Kids RC Toy Parts.
100% brand new and high quality.
High-quality and durable in performance.
Suitable for MG995 MG946R MG996R MG945 S3003 RC Model Motor
Specification:
Teeth Number : 25T
Over..
The Mounting L Bracket for NEMA17 Stepper Motor(Bend) is made from high-quality Hardened Mild Steel.
Mounting L clamp will fit any NEMA17 Motor (with 31 mm hole spacing) with four screws. L-shaped bracket with 90 degrees mounting angle, is designed for NEMA17 Stepper Motor to mount it on the app..